FiberKom mini-optical node equipped with Return Path transmitter and OLC technology (2 fibers) 1200...1600 nm, Return: 1310 nm, Po 3 dBm
Mini-optical node to act as a bridge between coaxial technology and optical networks. Transforms the optical signal (1200 nm-1600 nm) on the main network into a coaxial signal (54 MHz-1006 MHz) that travels to the user's modem.
It also transforms the coaxial modem's signal (5 MHz-42MHz) into an optical signal for the operator's headend, thanks to the the Return Path transmitter on the 1310 nm window with 3 dBm optical power.
Uses two fibers: one for the forward channel and the other for the Return Path.
Perfect for installations where the DOCSIS protocol is used for the bidirectional distribution of data, and the DVB-C standard is used for television signals.
Equipped with OLC technology.
Perfect for RF Overlay and FTTB applications.
It also transforms the coaxial modem's signal (5 MHz-42MHz) into an optical signal for the operator's headend, thanks to the the Return Path transmitter on the 1310 nm window with 3 dBm optical power.
Uses two fibers: one for the forward channel and the other for the Return Path.
Perfect for installations where the DOCSIS protocol is used for the bidirectional distribution of data, and the DVB-C standard is used for television signals.
Equipped with OLC technology.
Perfect for RF Overlay and FTTB applications.
Ref. 238081
EAN13:
8424450170809
SKU
238081
Televes reserves the right to modify the product
Highlights
- The OLC (Optical Level Control) technology automatically adjusts the parameters to achieve a constant output level, irrespective of the channel load
- Equipped with attenuation controls
- High output voltage (RF amplification) and enhanced C/N
- Wide reception optical range
- Very low power consumption
Main features
- DOCSIS compatible
- Two operation modes:
1. CW (Continuous Wave) in which the laser transmits continuously; useful in applications where the Return Path is attenuated (FTTB).
2. RFoG (RF over Glass) where the laser only transmits when there are packets to be transmitted; it is therefore recommended for installations with minimal attenuation on the Return Path (FTTH).
- SC/APC optical connectors, and F-type connectors for RF
- Local powering
| Forward path | ||
| Frequency range | MHz | 54 ... 1006 |
| Output impedance | Ohm | 75 |
| Optical input level for OLC | dBm | -8 ... +1dBm |
| Flatness | dB | ± 1 |
| Number of outputs | no. | 1 |
| Typical output level in OLC range | dBmV | 33 |
| CNR | dB | >52 |
| CSO | dB | >60 |
| CTB | dB | >60 |
| Equivalent noise current density at input | pA/ Hz | < 6 |
| Forward path attenuator | dB | 6/12 select. |
| Pre-emphasis | dB | 3 |
| Wavelength | nm | 1200 - 1600 |
| Optical return loss | dB | >40 |
| Optical connector | type | SC/APC |
| Max. optical input power before damage | dBm | 2 |
| Optical device | type | InGaAs pin photodiode |
| Return path | ||
| Frequency range (selectable) | MHz | 5 ... 42 |
| Input impedance | Ohm | 75 |
| Optical output level | dBm | 3 |
| Flatness | dB | ± 1 |
| RF input level | dBmV | 10 ... 35 |
| Return path attenuator | dB | 0/10/20 select. |
| Wavelength | nm | 1310 ±20 |
| Optical connector | type | SC/APC |
| Laser type | type | DFB (Class1M) |
|
Transmitter turn-on/off time |
μs | 1 |
| General | ||
| Local mains voltage | V~/mA | 99 / 75 ... 253 / 40 |
| Max. mains power | W | 4 |
|
Power voltage through RF connector |
Vdc/mA | - |
| Test point | dB | -30 ±1 |
| RF connectors | type | F |
| Housing material | Zamak/ABS | |
| Operating temperature | ºF | +23 .... +113 |
| Index operation | IP | 30 |
| EMC compatibility | EN 50083-2 | |
| Safety | EN 60825-1_2007 | |
